Single-channel 25G IPMX uncompressed transceiver with 12G-SDI
PlexusAV P-AVN-6-S
The P-AVN-6-S is a 1RU transceiver from PlexusAV, the professional AV division of Sencore, for organisations that run SDI cameras, switchers or monitors alongside a move to IP. It converts baseband SDI into IPMX and SMPTE ST 2110 streams and back again, so existing signal chains can be connected to an open-standard network without replacing the SDI equipment. Its target users are broadcast and live production crews, control rooms, houses of worship, government and corporate AV teams, and integrators building hybrid systems. The main benefit is flexibility: the same unit can send uncompressed video over high-speed fibre or copper links where they exist, and fall back to compressed JPEG XS over an existing 1GbE network elsewhere in the building.

Uncompressed 4K60 Over 25GbE IP Links
The P-AVN-6-S sends single-channel uncompressed IPMX and SMPTE ST 2110 video up to 4K60, at roughly 18 Gbps, over its dual SFP28 ports. Colour gamuts cover BT.709, BT.2020 and DCI-P3, and HDR10 and HLG are supported. Uncompressed transport avoids the latency and encoding artefacts that come with compressed codecs, which matters for live production, fast stream switching and any picture that will be graded or keyed downstream. For the end user this means the image arriving at a control room or display is the same quality as the source, provided the network has 10GbE or 25GbE capacity. The 25GbE path is the one that carries the full uncompressed bandwidth, so the installer should plan switch ports and cabling for it from the start.

Hitless ST 2022-7 Network Redundancy
Two independent SFP28 interfaces carry primary and secondary network paths, and ST 2022-7 hitless switching moves the stream between them without loss when one path fails. The datasheet describes this as zero-loss failover. For the end user, a failed cable, optic or switch port does not interrupt the program feed or the signal on the monitor. This is the feature that makes the unit suitable for command centres, government and defence networks, and live events where an outage during a session is not acceptable. Redundancy only works if the two paths are physically separate, so the installer should route them through different switches and cable runs.
One box. Uncompressed 4K60 on 25GbE, JPEG XS on 1GbE.
3-year limited warranty · 1RU, 1/3 RU width · Dual SFP28 with ST 2022-7

PTP-to-Genlock for Hybrid SDI and IP
The unit derives a genlock reference from IP-based PTP timing and outputs it on a dedicated BNC, which keeps SDI sources and IP streams locked to the same clock. The datasheet gives a phase accuracy of ±12 pixels when the genlock offset is near zero, and it supports NTSC and PAL black burst as well as tri-level sync in the common HD and SD rates. Hybrid facilities often need an external sync generator or timing converter to link an SDI camera to an IP timing domain; here the function is built in. For the operator this removes a box from the rack and a source of timing faults, and it keeps SDI cameras and IP-fed displays aligned during switching.

JPEG XS on Existing 1GbE Networks
For compressed transport, the P-AVN-6-S uses JPEG XS at up to 2.5 Gbps over its RJ45 port on standard 1 gigabit infrastructure. The same RJ45 port also provides PoE+ power input for redundant power. This lets a site run IPMX video on the copper network already installed, without a switch upgrade or new fibre. The trade-off is compression, so the picture is not identical to uncompressed transport, but for signage, meeting-room distribution and monitoring it keeps the project affordable. For the end user this typically means a working IP video feed on a network they already use, and a clear route to uncompressed quality later by adding 25GbE links.

Native 12G-SDI I/O With HDMI Loop-Out
The BNC 12G-SDI port auto-detects 12G, 6G, 3G and HD-SDI formats in both directions, so the same unit encodes an SDI input to IP and decodes an IP stream to SDI output. An HDMI 2.1a loop-out provides local monitoring of the incoming SDI source. Because no external converter is needed, the unit can take legacy baseband equipment into an IP system with a single device. The loop-out is practical for confidence monitoring at the source without a separate splitter. For the end user, existing cameras and switchers keep working, and the operator can check the signal on a local screen during setup or troubleshooting.

Web UI, REST API and NMOS Control
The P-AVN-6-S can be configured through a front-panel LCD and buttons, a browser-based HTTPS web interface, or a REST API. It supports NMOS IS-04, IS-05, IS-08, IS-09 and IS-11 for device discovery, connection management and audio mapping, and it integrates with PlexusAV Visual Array for centralised routing and monitoring across several units. Support for open control interfaces lets an integrator connect the device to third-party control systems rather than a single proprietary controller. For the end user, this makes routing changes and remote troubleshooting possible from one place, which reduces the time needed for system changes and support visits.

Dante and AES67 Audio Transport
Audio travels alongside the video over Dante and AES67, with up to 8x8 channels of Dante audio and up to eight channels in AES67. The datasheet also lists PCM, Dolby Digital/Plus/TrueHD/Atmos and DTS 5.1/HD/X codecs at 16 and 24-bit depth, and the unit has a balanced analogue audio input/output on a 5-pin Phoenix connector. Keeping audio on the same IP network as video removes separate audio cabling between rooms and devices. For the end user, the sound stays in step with the picture, and the installation needs fewer cables and fewer audio converters.